The Beneficial Impact of Mineral Content in Spent-Coffee-Ground-Derived Hard Carbon on Sodium-Ion Storage.

The key technological implementation of sodium-ion batteries is converting biomass-derived hard carbons into effective anode materials. This becomes feasible if appropriate knowledge of the relations between the structure of carbonized biomass products, the mineral ash content in them, and Na storage properties is gained. In this study, we examine the simultaneous impact of the ash phase composition and carbon structure on the Na storage properties of hard carbons derived from spent coffee grounds (SCGs). The carbon structure is modified using the pre-carbonization of SCGs at 750 °C, followed by annealing at 1100 °C in an Ar atmosphere. Two variants of the pre-carbonization procedure are adopted: the pre-carbonization of SCGs in a fixed bed and CO2 flow. For the sake of comparison, the pre-carbonized products are chemically treated to remove the ash content. The Na storage performance of SCG-derived carbons is examined in model two and three Na-ion cells. It was found that ash-containing carbons outperformed the ash-free analogs with respect to cycling stability, Coulombic efficiency, and rate capability. The enhanced performance is explained in terms of the modification of the carbon surface by ash phases (mainly albite) and its interaction with the electrolyte, which is monitored by ex situ XPS.

Agar Graft Modification with Acrylic and Methacrylic Acid for the Preparation of pH-Sensitive Nanogels for 5-Fluorouracil Delivery.

Agar, a naturally occurring polysaccharide, has been modified by grafting it with acrylic (AcA) and methacrylic (McA) acid monomers, resulting in acrylic or methacrylic acid grafted polymer (AA-g-AcA or AA-g-McA) with pH-sensitive swelling behavior. Different ratios between agar, monomers, and initiator were applied. The synthesized grades of both new polymer series were characterized using FTIR spectroscopy, NMR, TGA, DSC, and XRD to ascertain the intended grafting. The percentage of grafting (% G), grafting efficiency (% GE), and % conversion (% C) were calculated, and models with optimal characteristics were further characterized. The swelling behavior of the newly synthesized polymers was studied over time and in solutions with different pH. These polymers were subsequently crosslinked with varying amounts of glutaraldehyde to obtain 5-fluorouracil-loaded nanogels. The optimal ratios of polymer, drug, and crosslinker resulted in nearly 80% loading efficiency. The performed physicochemical characterization (TEM and DLS) showed spherical nanogels with nanometer sizes (105.7-250 nm), negative zeta potentials, and narrow size distributions. According to FTIR analysis, 5-fluorouracil was physically incorporated. The swelling and release behavior of the prepared nanogels was pH-sensitive, favoring the delivery of the chemotherapeutic to tumor cells. The biocompatibility of the proposed nanocarrier was proven using an in vitro hemolysis assay.

Biopolymeric Nanogel as a Drug Delivery System for Doxorubicin-Improved Drug Stability and Enhanced Antineoplastic Activity in Skin Cancer Cells.

In this study, doxorubicin was loaded in a chitosan-albumin nanogel with the aim of improving its stability and exploring the potential of the system in the treatment of skin cancer. Infrared spectroscopy and X-ray diffraction confirmed the encapsulation of the drug. Transmission electron microscopy revealed the spherical shape of the nanogel particles. The drug-loaded nanogel was characterized with a small diameter of 29 nm, narrow polydispersity (0.223) and positive zeta potential (+34 mV). The exposure of encapsulated doxorubicin to light (including UV irradiation and daylight) did not provoke any degradation, whereas the nonencapsulated drug was significantly degraded. In vitro studies on keratinocytes (HaCaT) and epidermoid squamous skin carcinoma cells (A-431) disclosed that the encapsulated doxorubicin was more cytotoxic on both cell lines than the pure drug was. More importantly, the cytotoxic concentration of encapsulated doxorubicin in carcinoma cells was approximately two times lower than that in keratinocytes, indicating that it would not affect them. Thus, the loading of doxorubicin into the developed chitosan-albumin nanogel definitely stabilized the drug against photodegradation and increased its antineoplastic effect on the skin cancer cell line.

Formulation of Budesonide-Loaded Polymeric Nanoparticles into Hydrogels for Local Therapy of Atopic Dermatitis.

Budesonide is a mineral corticoid applied in the local therapy of pediatric atopic dermatitis. Unfortunately, its dermal administration is hindered by the concomitant adverse effects and its physicochemical properties. The characteristic pH change in the atopic lesions can be utilized for the preparation of a pH-sensitive nanocarrier. In this view, the formulation of Eudragit L 100 nanoparticles as a budesonide delivery platform could provide more efficient release to the desired site, improve its penetration, and subsequently lower the undesired effects. In this study, budesonide-loaded Eudragit L100 nanoparticles were prepared via the nanoprecipitation method (mean diameter 57 nm, -31.2 mV, and approx. 90% encapsulation efficiency). Their safety was proven by cytotoxicity assays on the HaCaT keratinocyte cell line. Further, the drug-loaded nanoparticles were incorporated into two types of hydrogels based on methylcellulose or Pluronic F127. The formulated hydrogels were characterized with respect to their pH, occlusion, rheology, penetration, spreadability, and drug release. In conclusion, the developed hydrogels containing budesonide-loaded nanoparticles showed promising potential for the pediatric treatment of atopic dermatitis.

Study on the Dye Removal from Aqueous Solutions by Graphene-Based Adsorbents.

In the current investigation, the removal efficiency regarding a cationic dye, methylene blue (MB), from three graphene-based materials was investigated. The materials' characterization process involved instrumental methods such as XRD, XPS, SEM, TEM, FTIR, and nitrogen adsorption at 77 K. The survey examined how various process factors influenced the ability of the studied materials to adsorb cationic dyes. These parameters encompassed contact time, initial dye concentrations, solution pH, and temperature. The adsorption procedure was effectively explained through the application of pseudo-second-order and Langmuir models. The maximum adsorption capacity for the best adsorbent at 293 K was found to be 49.4 mg g-1. In addition, the study also determined the entropy, enthalpy, and Gibbs free energy values associated with the removal of MB and showed that the adsorption of MB is endothermic, feasible, and spontaneous. The results also revealed that the studied materials are suitable adsorbents for the removal of cationic dyes.

Thermosensitive Hydrogel-Functionalized Mesoporous Silica Nanoparticles for Parenteral Application of Chemotherapeutics.

Hydrogels can offer many opportunities for drug delivery strategies. They can be used on their own, or their benefits can be further exploited in combination with other nanocarriers. Intelligent hydrogels that react to changes in the surrounding environment can be utilized as gatekeepers and provide sustained on-demand drug release. In this study, a hybrid nanosystem for temperature- and pH-sensitive delivery was prepared from MCM-41 nanoparticles grafted with a newly synthesized thermosensitive hydrogel (MCM-41/AA-g-PnVCL). The initial particles were chemically modified by the attachment of carboxyl groups. Later, they were grafted with agar (AA) and vinylcaprolactam (VCL) by free radical polymerization. Doxorubicin was applied as a model hydrophilic chemotherapeutic drug. The successful formulation was confirmed by FT-IR and TGA. Transmission electron microscopy and dynamic light scattering analysis showed small particles with negative zeta potential. Their release behaviour was investigated in vitro in media with different pH and at different temperatures. Under tumour simulating conditions (40 °C and pH 4.0), doxorubicin was almost completely released within 72 h. The biocompatibility of the proposed nanoparticles was demonstrated by in vitro haemolysis assay. These results suggest the possible parenteral application of the newly prepared hydrogel-functionalized mesoporous silica nanoparticles for temperature-sensitive and pH-triggered drug delivery at the tumour site.

Doxorubicin and Quercetin Double Loading in Modified MCM-41 Lowered Cardiotoxicity in H9c2 Cardioblast Cells In Vitro.

BACKGROUND: One of the therapeutic limitations of the use of doxorubicin (DOX) as an anticancer drug is its cardiotoxicity. Its hydrophilicity also causes difficulties in achieving sustained release. The simultaneous delivery with the well-known natural antioxidant quercetin could ameliorate its cardiotoxicity. Thus, the main aim of this work is to study the potential of carboxylated and non-carboxylated mesoporous silica MCM-41 nanoparticles for double loading of the hydrophilic doxorubicin hydrochloride and hydrophobic quercetin (Q) in one nanocarrier with a modified release pattern to reduce the cardiotoxic side effects of doxorubicin in vitro. METHODS: The methods included the modification of MCM-41, single and double loading of modified and non-modified MCM-41, physicochemical characterization, in vitro release tests and kinetic study, and in vitro cell viability studies. RESULTS: Doxorubicin and quercetin were successfully double-loaded with encapsulation efficiency (EE) of 43 ± 4.1% and 37 ± 4.5%, respectively, in native MCM-41. The post-synthetic carboxylation led to 49 ± 4.3% EE (DOX) and 36 ± 4.0% (Q) and double lowering of the cardiotoxicity on H9c2 (IC50 = 5.96 µm). Sustained release profiles over 72 h were achieved. CONCLUSIONS: A successful procedure was proposed for the efficient double loading of a hydrophilic drug and a hydrophobic drug. The carboxy-modified double-loaded nanosystems demonstrate a decreased in vitro cardiotoxicity of doxorubicin and can be considered as a potential chemotherapeutic formulation.

Double-Loaded Doxorubicin/Resveratrol Polymeric Micelles Providing Low Toxicity on Cardiac Cells and Enhanced Cytotoxicity on Lymphoma Cells.

The anthracycline antibiotic doxorubicin is a well-known antitumour agent, however its cardiotoxicity is a significant obstacle to therapy. The aim of the present study was to improve the safety of doxorubicin through its simultaneous encapsulation with a cardioprotective agent (resveratrol) in Pluronic micelles. The formation and double-loading of the micelles was performed via the film hydration method. Infrared spectroscopy proved the successful incorporation of both drugs. X-ray diffraction analyses revealed that resveratrol was loaded in the core, whereas doxorubicin was included in the shell. The double-loaded micelles were characterised by a small diameter (26 nm) and narrow size distribution, which is beneficial for enhanced permeability and retention effects. The in vitro dissolution tests showed that the release of doxorubicin depended on the pH of the medium and was faster than that of resveratrol. In vitro studies on cardioblasts showed the opportunity to reduce the cytotoxicity of doxorubicin through the presence of resveratrol in double-loaded micelles. Higher cardioprotection was observed when the cells were treated with the double-loaded micelles compared with referent solutions with equal concentrations of both drugs. In parallel, treatments of L5178 lymphoma cells with the double-loaded micelles revealed that the cytotoxic effect of doxorubicin was enhanced. Thus, the study demonstrated that the simultaneous delivery of doxorubicin and resveratrol via the micellar system enabled the cytotoxicity of doxorubicin in lymphoma cells and lowered its cardiotoxicity in cardiac cells.

Formulation of Nanomicelles Loaded with Cannabidiol as a Platform for Neuroprotective Therapy.

The present study is focused on the development of cannabidiol-loaded polymeric nanomicelles as a drug delivery system with neuroprotective effects. Cannabidiol was loaded in Pluronic micelles (Pluronic P123 or its combination with Pluronic F127) possessing an average diameter smaller than 50 nm and high encapsulation efficiency for the hydrophobic drug (80% and 84%, respectively). The successful encapsulation and transformation of cannabidiol in amorphous phase were observed by IR spectroscopy and X-ray diffraction, respectively. Studies with neuroblastoma cells (SH-SY5Y and Neuro-2a) showed that the pure cannabidiol caused a dose-dependent reduction of cell viability, whereas its loading into the micelles decreased cytotoxicity. Further, neuroprotective effects of pure and micellar cannabidiol were examined in a model of H2O2-induced oxidative stress in both neuroblastoma cells. The pre-treatment of cell lines with cannabidiol loaded into the mixed Pluronic P123/F127 micelles exerted significantly stronger protection against the oxidative stress compared to pure cannabidiol and cannabidiol in single Pluronic P123 micelles. Interestingly, the empty mixed P123/F127 micelles demonstrated protective activity against the oxidative stress. In conclusion, the study revealed the opportunity to formulate a new drug delivery system of cannabidiol, in particular nanosized micellar aqueous dispersion, that could be considered as a perspective platform for cannabidiol application in neurodegenerative diseases.

Novel Nanosized Spinel MnCoFeO4 for Low-Temperature Hydrocarbon Oxidation.

The present paper reports on MnCoFeO4 spinels with peculiar composition and their catalytic behavior in the reactions of complete oxidation of hydrocarbons. The samples were synthesized by solution combustion method with sucrose and citric acid as fuels. All samples were characterized by powder X-ray diffraction, N2-physisorption, scanning electron microscopy, thermal analysis, X-ray photoelectron spectroscopy, and Mössbauer spectroscopy. The catalytic properties of the spinels with Mn:Co:Fe = 1:1:1 composition were studied in reactions of complete oxidation of methane, propane, butane, and propane in the presence of water as model pollutants. Both prepared catalysts are nanosized materials. The slight difference in the compositions, structure, and morphology is due to the type of fuel used in the synthesis reaction. The spinel, prepared with sucrose, shows a higher specific surface area, pore volume, higher amount of small particles fraction, higher thermal stability, and as a result, more exposed active sites on the sample surface that lead to higher catalytic activity in the studied oxidation reactions. After the catalytic tests, both samples do not undergo any substantial phase and morphological changes; thus, they could be applied in low-temperature hydrocarbon oxidation reactions.

Facile Synthesized Cu-RGO and Ag-RGO Nanocomposites with Potential Biomedical Applications.

In the present study, we report on the facile prepared nanocomposites of reduced graphene oxide RGO with Cu and Ag. The synthesis was performed through an environmentally friendly and easy method by simultaneous reduction in solutions containing Cu2+ or Ag+ and graphene oxide (GO) using zinc powder as a reducing agent in aqueous acidic media. The composites are characterized by powder X-ray diffraction, low-temperature nitrogen adsorption, X-ray photoelectron and FTIR and Raman spectroscopies, as well as Scanning and Transmission electron microscopies. The antibacterial activity of the composites was tested for Staphylococcus aureus, Escherichia coli and antifungal activity for Candida albicans. The cytotoxicity of the materials was studied towards two types of eukaryotic cells-MDCK II and A549 cell lines. The composites obtained consist of homogeneously distributed Cu and Ag nanoparticles on the surface of graphene sheets and manifest good antimicrobial activity and high cytotoxicity. The results clearly show that both metal-RGO composites can be successfully used as antimicrobial and anticancer agents.

Nickel-Decorated Mesoporous Iron-Cerium Mixed Oxides: Microstructure and Catalytic Activity in Methanol Decomposition.

Nickel-decorated mesoporous cerium-iron oxide composites were synthesized by a combination of incipient wetness impregnation and template-assisted hydrothermal techniques. The effects of the Fe/Ce ratio and the calcination temperature of cerium-iron oxides on the phase composition, texture, structure, and redox properties of the composites were studied by a combination of N2 physisorption, XRD, high-resolution transmission electron microscopy, SEM, Mössbauer, Raman, XPS, ultraviolet-visible and FTIR spectroscopies, H2-temperature-programmed reduction, and total oxidation of ethyl acetate as a catalytic test. The combined physicochemical characterization and in situ FTIR investigation of methanol decomposition was used for a proper understanding of the microstructure of the Ni/FeCe oxide composites and the mechanism of the reaction occurring on them. The complex role of the FeCe support in the stabilization of highly dispersed Ni particles, the generation of surface intermediates, and the impact of the support phase transformation under the reaction medium are discussed.

Improvement of the Antimicrobial Activity of Oregano Oil by Encapsulation in Chitosan-Alginate Nanoparticles.

Oregano oil (OrO) possesses well-pronounced antimicrobial properties but its application is limited due to low water solubility and possible instability. The aim of this study was to evaluate the possibility to incorporate OrO in an aqueous dispersion of chitosan-alginate nanoparticles and how this will affect its antimicrobial activity. The encapsulation of OrO was performed by emulsification and consequent electrostatic gelation of both polysaccharides. OrO-loaded nanoparticles (OrO-NP) have small size (320 nm) and negative charge (-25 mV). The data from FTIR spectroscopy and XRD analyses reveal successful encapsulation of the oil into the nanoparticles. The results of thermogravimetry suggest improved thermal stability of the encapsulated oil. The minimal inhibitory concentrations of OrO-NP determined on a panel of Gram-positive and Gram-negative pathogens (ISO 20776-1:2006) are 4-32-fold lower than those of OrO. OrO-NP inhibit the respiratory activity of the bacteria (MTT assay) to a lower extent than OrO; however, the minimal bactericidal concentrations still remain significantly lower. OrO-NP exhibit significantly lower in vitro cytotoxicity than pure OrO on the HaCaT cell line as determined by ISO 10993-5:2009. The irritation test (ISO 10993-10) shows no signs of irritation or edema on the application site. In conclusion, the nanodelivery system of oregano oil possesses strong antimicrobial activity and is promising for development of food additives.

Spectral and Texture Properties of Hydrophobic Aerogel Powders Obtained from Room Temperature Drying.

Attenuated Total Reflectance Infrared (ATR-IR) spectroscopy and texture measurements based on nitrogen adsorption-desorption isotherms are combined to characterize silica aerogel granules with different degrees of hydrophobicity. The aerogels were prepared from tetraethoxysilane via a room temperature hydrolysis-gelation process, solvent exchange, hydrophobization, and drying at subcritical conditions. The dependencies between the texture properties, pore architectures, surface fractal dimensions, and degree of hydrophobicity of the samples are extracted from the ATR-IR spectra and the adsorption-desorption isotherms. The IR absorption in the region of the Si-O-Si and Si-OH vibrations is used for a description of the structural and chemical changes in aerogel powders connected with their surface hydrophobization. The Frenkel-Halsey-Hill (FHH) theory is applied to determine the surface fractal dimension of the powder species.

In vitro toxicity evaluation of lomefloxacin-loaded MCM-41 mesoporous silica nanoparticles.

Lomefloxacin (LF) is interesting as a model molecule from a safety point of view because of its high potential for serious adverse drug effects (i.e. phototoxic reactions). In this study, MCM-41 mesoporous silica nanoparticles (MCM-41) were loaded with lomefloxacin, aiming to overcome the drug's intrinsic cytotoxicity. The good biocompatibility of the empty drug carrier (0.1-1.0 mg/ml) was established by the absence of red blood cell lysis (hemolysis assay). The cytotoxicity of empty MCM-41 and lomefloxacin-loaded MCM-41 (LF-MCM-41) was evaluated by using a battery of in vitro cytotoxicity assays: Alamar blue, lactate dehydrogenase release and reactive oxygen species formation by dichlorofluorescein assay. Three cell cultures models: hepatoma HepG2, fibroblasts L929 and endothelial EA.hy926 cells were used to compare the cytotoxicity and reactive oxygen species formation by free drug, empty MCM-41, and LF-MCM-41. The findings from the study indicated that empty MCM-41 (0.1-1.0 mg/ml) showed a low cytotoxic potential in HepG2, followed by L929 and EA.hy926 cells. Lomefloxacin loading in MCM-41 mesoporous silica nanocarrier reduced the cytotoxicity of the free lomefloxacin, especially in the high concentration (1.0 mg/ml MCM-41, containing 120 µg/ml LF). L929 and EA.hy926 cells were more sensitive to the protective effects of LF-MCM-41, compared to HepG2 cells. The results indicate that an improvement in lomefloxacin safety might be expected after incorporation in an appropriate drug delivery system.

Formation of Catalytic Active Sites in Hydrothermally Obtained Binary Ceria-Iron Oxides: Composition and Preparation Effects.

A series of mesoporous cerium-iron binary oxides was prepared by a hydrothermal technique using CTAB as a template. The influence of the Fe/Ce ratio and the variations in the preparation techniques such as the type of solvent and the precipitation agent, the approach of the template release, and the temperature of calcination on the phase composition, textural, structural, surface, and redox properties of the obtained materials was studied in details by XRD, nitrogen physisorption, TPR, FTIR, UV-vis, XPS, Raman, and Moessbauer spectroscopies. The materials were tested as catalysts in methanol decomposition and total oxidation of ethyl acetate. It was assumed that the binary materials represented a complex mixture of differently substituted ceria- and hematite-like phases. Critical assessment of their formation on the base of a common mechanism scheme was proposed. This scheme declares the key role of the formation of shared Ce-O-Fe structures by insertion of Fe3+ in the ceria lattice and further competitive compensation of the lattice charge balance by the existing in the system ions, which could be controlled by the Fe/Ce ratio and the hydrothermal synthesis procedure used. This mechanism provides proper understanding and regulation of the catalytic behavior of cerium-iron oxide composites in methanol decomposition with a potential for hydrogen production and total oxidation of ethyl acetate as a model of VOCs.

Mixed Metal Oxides of the Type CoxZn1-xFe2O4 as Photocatalysts for Malachite Green Degradation Under UV Light Irradiation.

A combination of thermal and mechanical (high energy ball milling) treatment was applied in an attempt to obtain polycrystalline mixed metal binary and ternary oxides of the type CoxZn1-xFe2O4 (x = 0; 0.25; 0.5; 0.75; 1). The synthetic procedure used successfully produced single-phased, homogeneous ZnFe2O4, CoFe2O4, and Co0.75Zn0.25Fe2O4, as well as mixed oxides, whose composition depended both on the duration of the high energy ball milling and the ratio Zn(II)/Co(II). The formation of spinel-like structures was proved by XRD, Mössbauer spectroscopy and Raman spectroscopy. For the characterization of the samples low-temperature N2 adsorption, UV/Vis spectroscopy and transmission electron microscopy were applied. The energy band gap of the samples was calculated, suggesting they are promising photocatalysts. The decomposition of the Malachite Green in model water solutions under UV-light irradiation was successfully achieved in the presence of the samples as photocatalysts. The highest rate constant was obtained for the sample synthesized at longer milling time in combination with higher Zn(II)/Co(II) ratio. The photocatalytic activity of the ternary mixed oxides was compared with the pure hematite, α-Fe2O3, and the binary ZnFe2O4 and CoFe2O4 ferrites with spinel structure that were treated in the same way. A synergetic effect of α-Fe2O3 and the spinel-like structure on the photocatalytic properties of ternary mixed metal oxides was detected.